Search
KAIWEETS HT206D Clamp Meter, 6000 Counts Auto-Range Multimeter 600A AC/DC Current, 600V AC/DC Voltage with LCD Backlit, Capacitance, Continuity, Resistance, Duty, Diodes, Frecruncy, Temperature, NCV
Select options
Select
Shipping
£11.99
About this shop
ToyHub Store
Product description
To measure Direct CurrentApplication in automobile repair, DIY, etc.
Specifications:
If current> 3A, the orange display lights up.
The measuring range of DC current is 60A/600A. Accuracy: ±(2.5%+5).
Note:
Before measuring the DC current, long-press and hold the Z/F key until the ZERO character appears to clear the data.
To measure Alternating CurrentPress the "Z/F" button to swith to AC/DC Measurement
Note:
To measure the current you need to clamp the meter around one of the wires and not the whole power cord. The power cord contains two wires carrying current and ground wire. The current in two wires always flows in opposite directions, so the magnetic fields from two wires canceling each other, therefore the meter reads 0 A.
Grasp the individual current conductor to be measured and close the current clamp again. The measured conductor must be placed in the center of the clamp, otherwise, additional errors will occur.
Before taking dc current measurements, wait for the display to stabilize, then push the Zero button to ensure correct readings. Zeroing the meter removes dc offset from the reading. The Zero function works only when the dial is set in in the dc current measurement position. Note: Before zeroing the meter, make sure the jaws are closed and no conductor is inside the jaw.
Specifications
DC Voltage: 600mV/6V/60V/600V ±(0.5%+3)
AC Voltage: 6V/60V/600V ±(1.0%+3)
DC-Current: 60A/600A ±(2.5%+5)
AC-Current: 60A/600A ±(2.5%+5)
Resistance(ohms): 600Ω/6kΩ/60kΩ/600kΩ/6MΩ/60MΩ ±(1.0%+3)
Capacitance: 10nF/100nF/1mF/10mF/100mF ±(4.0%+3)
Frecuencia: 10Hz/100Hz/1kHz/10kHz/100kHz/1MHz/10MHz ±(0.5%+5)
Temperature: (℃, ℉)-40℃~1000±(1.0%+2) -40℉~1832℉ ±(1.0%+2)
Packing List
Jaw Design
The Jaw is marked with maximum voltage (600V) and current (600A) measured value. Suitable for one-hand operation.
Lightweight & Portable
Only weights 216g.
Small Size: 19.5 x 7.5 x 3 cm.
Easy to carry and put into your pocket or tool bag.
LCD Backlit Display
1 second press down "sun symbol" button to open LCD backlit, you can recognize any test value clearly even in dark place
NCV Function & Flash Light
NCV is a good function for the beginner, you can measure the voltage without touching any wire. Come with a flash light on the top, suit for low light condition
"Z/F" Button for Switching Function
Press the "Z/F" button to switch the respective secondary function between the different measurements such as diode, capacitance, continuity, resistance and switch AC and DC measured.
Automatic Shutdown
No operation in 15 minutes, the clamp meter beeps 3 times. Without further operation, it beeps again and switches off automatically.
Multi-Function
Accurately measure resistance, capacitance, diode, continuity. Easy to use in laboratory factories and homes.
【True-RMS】: This clamp multimeter can accurately measure AC/DC Current, AC/DC Voltage, Frequency or Duty Cycle, Resistance, Capacitance and also provides Diode, Continuity and Temperature tests. True RMS for accurate measurements on non-linear loads. Easy to use for labs, factories and household.
【LowZ & LPF】: Low input impedance helps prevent false readings due to ghost voltage. Low Pass Filter (LPF) for accurate measurement of variable frequency drive signals when measuring motors and transformer. To measure the current you need to clamp the meter around one of the wires instead of the whole power cord.
【NCV Function】: Non-contact voltage detection effectively check electrical status through measuring EM field intensity without touching any wires; The NCV button lies on the right side. Simply place your thumb on it and push. Safety standard IEC 61010-1, CAT III 600V. Double insulation.
【Multi-Function】: Two-color backlit display - When the voltage > 80V or the current > 3A, the LCD backlit turns orange to warn you of high voltage, addition function: LED Flashlight / Temperature Testing for liquids and air condition/ Low Battery Indication / Auto power off after 15 minutes inactivity.
【What You Get】: 1* Digital Clamp Meter, 1* Test Leads, 1 * Thermocouples, 2 * AAA batteries, 1* Storage Bag, 1 * User Manual. 3-Year after-sale service and lifetime technical support. Please contact with us if you have any concerns