Instant Water Heater Frequency Conversion Thermostat Tankless Heater G1/2 Connector 220V Instant Water Heater Household Supplies

Hign-concerned Chemical: None

Type: Hand Tool Parts

 

 

 

Specification:

Item Type: Water Heater Color: As shown in the picture Weight: Approx. 1500g / 52.9oz Rated Power: 5500W Rated Voltage: 220V Rated Water Pressure: 0.6MPa Wire Configuration: Wire length is about 0.55m / 1.8ft Minimum Water Inlet Pressure: 0.05MPa Maximum Water Inlet Pressure: 0.6MPa Water Pipe G1/2 Control Method: Touch screen Shell Material: ABS Shell + PVC Film Heating Body: Cast aluminum heater Temperature Setting Range: 35-55℃ Heating Mode: Circulating heating Installation Notes: 1. This product must be installed by qualified professionals. 2. Prepare percussion drill (drill diameter 6mm), adjustable wrench, cross screwdriver, electrician's knife and other auxiliary tools. 3. Check whether the electric meter and the air switch wire meet the installation and use requirements; whether the grounding wire is really introduced into the earth. 3.1) The ground wire must be reliably grounded. 3.2) Please be sure to install an air switch with leakage protection. 4. Refer to the length of the power cord and the installation position of the air switch. Position the installation and positioning size of the machine on the wall, punch holes, and insert expansion screws; screw on the mounting screws and the distance from the wall about 3mm, then hang the water heater, and then screw the lower fixing screw 5. Connect the copper core power cord live wire L (brown or red); neutral wire N (blue); ground wire (yellow-green two-color wire) to the corresponding air switch or wiring terminal and tighten it to ensure a reliable connection. 6. Connect the tap water pipe to the water inlet of the machine closely; then connect the water outlet to other terminal equipment with a hose. 7. If it is a newly installed pipeline, when installing it for the first time, please drain the impurities from the pipeline before connecting with the machine. 8. The anti-falling screw is installed on the top of the machine to prevent the machine from falling due to accidental touch. Note: Sealing gaskets must be added to the water inlet and outlet pipe joints. When fixing the hose joint screws with a wrench, do not use too much force to avoid damage to the gasket and cause water leakage and damage the machine. How to Use After using for the first time or after the water is cut off, the power should be turned off first, and then the water valve should be opened. Only when the water outlet pipeline has continuous water flow, it can be powered on; (If you do not do this, it may damage the product) 1). Display screen: It is fully displayed when power on. The digital screen is dark and bright in standby, and it displays the water temperature state when it is long on, and the set temperature state when it is flashing. The screen flashes when heating, indicating that the water flow is low or the temperature is high. When "LL" is displayed, it means that the water flow is too large and the temperature is too low; When “E*” is displayed, it means that the self-check of the machine is faulty and the heating is stopped at this time. When "- -" is displayed, it indicates the shutdown state, and the shutdown does not heat up. Temperature setting range: 35-55℃. Cycle plus temperature setting. 2). Touch button: The left button is the power switch key; long press for 3 seconds to turn on or off. The right key is the temperature setting key, and the temperature is added cyclically. The buzzer will beep every time there is a button operation. 3). This product model has a sleep function. When there is no operation and water flow, it will enter the sleep state after 6 seconds, that is, the dark and bright display state. When there is operation and water flow, it will immediately display the brightest. 4). This product model has constant power and constant temperature heating modes, and the heating mode is automatically selected according to the use environment and heating conditions. When the heating temperature reaches 55°C in the constant power heating mode, the heating is stopped, and when the temperature drops below the set temperature, the heating starts. When the working conditions are available, the machine prefers to use the constant temperature mode.

 

Package List:

1 x Water Heater

1 x English Manual

1 x Control Valve

1 x Screw Accessory Kit

1 x Screwdriver